Dämpfungsglied-Rechner
T-, Pi-, Bridged-T- und Reflexionsdämpfer
Required Parameters
Waiting for input data...
Quick Answer
An RF attenuator reduces signal power by a precise dB amount while maintaining impedance matching. For a T-pad in 50 ohm: R_series = Z0 x (K-1)/(K+1), R_shunt = 2Z0K/(K^2-1), where K = 10^(dB/20).
HF-Daempfungsglied-Rechner
Entwerfen Sie T-Glied, Pi-Glied und Bridged-T Daempfungsglieder fuer HF- und Audio-Anwendungen.
T-Glied Daempfungsglied
- R1 = Z0 x (K - 1) / (K + 1) wobei K = 10^(A/20)
- R2 = 2 x Z0 x K / (K^2 - 1)
Verwandte Werkzeuge
- dBm-zu-Watt-Rechner
- Ohmsches Gesetz Rechner
Design Notes
Resistive attenuators are frequency-independent in theory, but parasitic inductance and capacitance of physical resistors limit the usable frequency range. Through-hole pads work to about 100 MHz; SMD 0402 pads extend to 6 GHz. For broadband precision, use thin-film attenuator chips rated for your frequency range. Always verify return loss (>20 dB) and ensure each resistor can handle its share of the dissipated power.
Common Mistakes
- 1
Using a simple voltage divider instead of a matched-impedance pad — this causes reflections and VSWR problems.
- 2
Ignoring resistor power dissipation — at high attenuation, nearly all input power is dissipated as heat in the resistors.
- 3
Using wirewound resistors at RF frequencies — parasitic inductance destroys the flat frequency response above a few MHz.
Engineering Handbox
1. Calculate K = 10^(6/20) = 10^0.3 = 1.995\n2. R_series = 50 x (1.995-1)/(1.995+1) = 50 x 0.332 = 16.6 ohm\n3. R_shunt = 2 x 50 x 1.995 / (1.995^2 - 1) = 199.5 / 2.98 = 66.9 ohm
Knowledge Base
Wofür wird ein Pi-Dämpfungsglied verwendet?
Zur Reduzierung der Signalleistung bei gleichzeitiger Erhaltung der Wellenimpedanz (50 oder 75 Ohm), um Reflexionen und VSWR-Probleme zu vermeiden.
Wie wähle ich zwischen T- und Pi-Glied?
T-Glieder haben niedrigere Shuntkapazität (besser für HF). Pi-Glieder sind auf PCBs einfacher umzusetzen. Unter 1 GHz ist der Unterschied minimal.
Was ist die T-Glied-Formel?
R_serie = Z0 × (K-1)/(K+1), R_shunt = 2 × Z0 × K / (K²-1), wobei K = 10^(dB/20).
Welche Widerstandstoleranz für Dämpfungsglieder?
Labor: mindestens 1% Metallfilm. Produktion HF: 0,1% Präzisionswiderstände bei hoher Dämpfung.
Wie kaskadiere ich Dämpfungsglieder?
Einfach dB-Werte addieren. 3 dB + 6 dB = 9 dB Gesamtdämpfung. Jedes Glied muss die Systemimpedanz einhalten.
Related Engineering Tools
dBm to Watts Conversion
RF power conversion both ways
Voltage Divider Calculator
Loaded and unloaded divider output voltage
Trace Impedance Calculator
Microstrip and stripline baseline impedance
Frequency to Wavelength Conversion
Convert frequency and wavelength with velocity factor