LDO Voltage Regulator Calculator
Dropout, power dissipation, and thermal analysis
Required Parameters
Waiting for input data...
Quick Answer
LDO power dissipation: P = (Vin - Vout) × Iload. Junction temp: Tj = Ta + P × θJA. Ensure Tj < 125°C.
Design Notes
LDOs are simple but waste power as heat. Efficiency = Vout/Vin. For a 5V→3.3V conversion at 500mA, you dissipate 0.85W. Always check the dropout voltage spec at your load current — it increases with current. Use input and output capacitors (typically 1µF-10µF ceramic) for stability.
Common Mistakes
- 1
Forgetting that dropout voltage increases with load current — check the datasheet curves.
- 2
Ignoring thermal limits — a SOT-23 package can only dissipate ~0.4W without a heatsink.
- 3
Using an LDO where a switching regulator would be far more efficient (large Vin-Vout differential).
Knowledge Base
What is an LDO voltage regulator?
An LDO (Low Dropout Regulator) is a linear voltage regulator that can operate with a very small input-to-output voltage differential (dropout voltage), typically 100-500mV. Unlike switching regulators, LDOs produce clean output with minimal noise, making them ideal for powering analog circuits, ADCs, and RF stages.
How do I calculate LDO power dissipation?
P = (Vin - Vout) × Iload. For example, 5V to 3.3V at 500mA: P = (5 - 3.3) × 0.5 = 0.85W. This power is entirely converted to heat. Always verify the junction temperature: Tj = Tambient + P × θJA. If Tj exceeds 125°C (most LDOs' max), you need a heatsink, copper pour, or a switching regulator instead.
When should I use an LDO vs a switching regulator?
Use LDO when: (1) Low noise required (analog/RF/audio), (2) Vin - Vout < 2V, (3) Current < 500mA, (4) PCB space is tight, (5) Cost is critical. Use switching when: (1) Efficiency matters (battery), (2) Large Vin-Vout differential, (3) High current, (4) Step-up needed. LDO efficiency = Vout/Vin, so 3.3V from 5V = 66% vs ~90% for a buck converter.
What is dropout voltage?
The minimum Vin - Vout for the LDO to maintain regulation. True LDOs: 100-300mV at rated current. Quasi-LDOs: 500-700mV. Standard regulators (like 7805): 1.5-2V. Dropout increases with load current. Always check the datasheet graph 'Dropout vs. Load Current' at your operating temperature.
How do I choose input and output capacitors for an LDO?
Output cap: 1µF-10µF ceramic (X5R/X7R) minimum, close to output pin. Provides stability and transient response. Input cap: 1µF-10µF ceramic, close to input pin. Reduces source impedance. Some older LDOs require ESR in a specific range for stability — check the datasheet. Modern LDOs are stable with low-ESR MLCC.
What are popular LDO ICs?
3.3V: AMS1117-3.3 (1A, cheap), MCP1700 (250mA, low Iq), AP2112K (600mA, low noise). 5V: LM7805 (classic, 1.5A, not true LDO). Adjustable: LM317 (classic), TLV757P (1A, ultra-low noise), AP7361C (1A, 300mV dropout). For battery: ME6211 (500mA, 100mV dropout, 40µA Iq).
Related Engineering Tools
Battery Life Calculator
Estimate runtime from capacity and load current
Three Phase Calculator
Real, apparent, and reactive power
Transformer Turns Ratio Calculator
Voltage, current, and impedance transformation
Buck/Boost Converter Calculator
Duty cycle, inductor, and ripple sizing